Cylinder head bolts are the most important fasteners on an engine: too loose and the head gasket leaks, too tight (or tightened in the wrong order) and you stretch or break bolts, warp the head or pull threads out of the block. This page lists the cylinder head bolt torque specifications for Toyota engines from 1967 to 2008 – petrol, diesel, 4-cylinder, 6-cylinder, V6 and V8 – with every value in both ft-lbf and N·m.
How to read the tables
- “1st 36, 2nd +90°” means: tighten all bolts in sequence to 36 ft-lbf (49 N·m), then turn each bolt a further 90° (a quarter turn) in the same sequence.
- “in three steps” means: reach the final torque gradually in three even passes, following the sequence each time.
- “Bolts 1–8 … bolts 9–10”: some engines use different bolts in different positions. The numbers refer to the tightening sequence for that engine.
- 12-point and recessed bolts (V6 engines such as the 1MZ-FE and 5VZ-FE): the main 12-point head bolts are tightened by torque plus angle; the small recessed bolts at the end of the head are tightened last, by torque only.
- Model years are those of the source (mostly North American model years).
Torque-to-yield head bolts: never reuse them
Every procedure that ends with “+90°” uses torque-to-yield (TTY) bolts. They are designed to stretch slightly into their yield zone to give an even clamping force over the whole gasket. Once stretched, they cannot clamp correctly a second time. Toyota’s repair manuals give a maximum bolt length or minimum thread diameter: if a bolt is out of limit, or you are not sure, replace it – new head bolts are cheap compared with a second head gasket job.
Good practice when tightening Toyota head bolts
- Clean the bolt holes in the block (blow out oil and coolant – liquid trapped in a blind hole can crack the block or give a false torque reading).
- Check the head and block surfaces for flatness with a straightedge and feeler gauge.
- Apply a light coat of engine oil to the bolt threads and under the bolt heads, as Toyota specifies, unless the gasket or bolt maker says otherwise.
- Tighten in the correct sequence – usually from the centre of the head outwards in a spiral – and in several passes.
- For angle steps, use an angle gauge, or paint a mark on each bolt head and turn until the mark has moved a quarter turn.
- Do not re-torque TTY bolts after the engine has run unless the procedure says so.
Modern 4-cylinder petrol engines (torque-to-yield bolts)
| Engine | Displacement | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|
| 1NZ-FE | 1.5 L DOHC 16V | 2000–2008 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 1NZ-FXE (Prius hybrid) | 1.5 L DOHC 16V | 2001–2008 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 5E-FE | 1.5 L DOHC 16V | 1992–1999 | 1st 33 ft-lbf (45 N·m), 2nd +90° |
| 4A-FE | 1.6 L DOHC 16V | 1993–1997 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 4A-GE | 1.6 L DOHC 16V | 1988–1991 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 4A-GZE (supercharged) | 1.6 L DOHC 16V | 1988–1989 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 7A-FE | 1.8 L DOHC 16V | 1993–1997 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 1ZZ-FE | 1.8 L DOHC 16V | 1998–2008 | 1st 36 ft-lbf (49 N·m), 2nd +90° |
| 2ZZ-GE | 1.8 L DOHC 16V | 2000–2006 | 1st 26 ft-lbf (35 N·m), 2nd +90°, 3rd +90° |
| 1AZ-FE | 2.0 L DOHC 16V | 2001–2003 | 1st 36 ft-lbf (49 N·m), 2nd +90°, 3rd +90° |
| 3S-FE | 2.0 L DOHC 16V | 1996–2000 | 1st 36 ft-lbf (49 N·m), 2nd +90°, 3rd +90° |
| 3S-FE | 2.0 L DOHC 16V | 1990–1992 | 1st 36 ft-lbf (49 N·m), 2nd +90° |
| 3S-GTE (turbo) | 2.0 L DOHC 16V | 1990–1995 | 1st 36 ft-lbf (49 N·m), 2nd +90° |
| 5S-FE, 5S-NFE | 2.2 L DOHC 16V | 1990–2001 | 1st 36 ft-lbf (49 N·m), 2nd +90° |
| 2AZ-FE (Camry, Solara) | 2.4 L DOHC 16V | 2002–2006 | 1st 58 ft-lbf (79 N·m), 2nd +90° |
| 2AZ-FE (Camry, Solara) | 2.4 L DOHC 16V | 2007–2008 | 1st 52 ft-lbf (71 N·m), 2nd +90° |
| 2AZ-FE (RAV4) | 2.4 L DOHC 16V | 2004–2005 | 1st 58 ft-lbf (79 N·m), 2nd +90° |
| 2AZ-FE (RAV4) | 2.4 L DOHC 16V | 2006–2008 | 1st 52 ft-lbf (71 N·m), 2nd +90° |
| 2AZ-FE (Highlander) | 2.4 L DOHC 16V | 2001–2007 | 1st 58 ft-lbf (79 N·m), 2nd +90° |
| 2AZ-FXE (Camry hybrid) | 2.4 L DOHC 16V | 2007–2008 | 1st 52 ft-lbf (71 N·m), 2nd +90° |
| 2RZ-FE | 2.4 L DOHC 16V | 1995–2004 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
| 2TZ-FE | 2.4 L DOHC 16V | 1991–1996 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
| 2TZ-FZE (supercharged) | 2.4 L DOHC 16V | 1994–1997 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
| 2TR-FE | 2.7 L DOHC 16V | 2005–2008 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
| 3RZ-FE | 2.7 L DOHC 16V | 1994–2004 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
Older 4-cylinder petrol engines
| Engine | Displacement | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|
| K (KC) | 1.1 L OHV 8V | 1968–1969 | 39–48 ft-lbf (53–65 N·m) |
| 3K (3KC) | 1.2 L OHV 8V | 1969–1979 | 39–48 ft-lbf (53–65 N·m) |
| 4K (4KC, 4KE) | 1.3 L OHV 8V | 1981–1984 | 40–47 ft-lbf (54–64 N·m) |
| 1A, 3A (1AC, 3AC) | 1.5 L SOHC 8V | 1980–1988 | 40–47 ft-lbf (54–64 N·m) |
| 3E | 1.5 L SOHC 12V | 1987–1990 | 1st 22 ft-lbf (30 N·m), 2nd 36 ft-lbf (49 N·m), 3rd +90° |
| 3E-E | 1.5 L SOHC 12V | 1990–1994 | 1st 22 ft-lbf (30 N·m), 2nd 36 ft-lbf (49 N·m), 3rd +90° |
| 4A-C, 4A-LC | 1.6 L SOHC 8V | 1983–1988 | 40–47 ft-lbf (54–64 N·m) |
| 4A-F | 1.6 L DOHC 16V | 1988–1989 | 40–47 ft-lbf (54–64 N·m) |
| 4A-FE | 1.6 L DOHC 16V | 1988–1989 | 40–47 ft-lbf (54–64 N·m) |
| 4A-FE | 1.6 L DOHC 16V | 1990–1992 | 44 ft-lbf (60 N·m), in three steps |
| 4A-GEC | 1.6 L DOHC 16V | 1985–1987 | 40–47 ft-lbf (54–64 N·m) |
| 4A-GELC | 1.6 L DOHC 16V | 1985–1989 | 44 ft-lbf (60 N·m), in three steps |
| 2T, 2TC | 1.6 L OHV 8V | 1971–1979 | 62–68 ft-lbf (84–92 N·m) |
| 3TC | 1.8 L OHV 8V | 1980–1982 | 62–68 ft-lbf (84–92 N·m) |
| 8R, 8RC | 1.9 L SOHC 8V | 1969–1971 | 75–85 ft-lbf (102–115 N·m) |
| 18RC | 2.0 L SOHC 8V | 1972–1974 | 75–85 ft-lbf (102–115 N·m) |
| 2S-ELC | 2.0 L SOHC 8V | 1983–1986 | 47 ft-lbf (64 N·m), in three steps |
| 3S-FE | 2.0 L DOHC 16V | 1987–1989 | 47 ft-lbf (64 N·m), in three steps |
| 3S-GELC | 2.0 L DOHC 16V | 1986–1989 | 40 ft-lbf (54 N·m), in three steps |
| 3S-GTE (turbo) | 2.0 L DOHC 16V | 1988–1989 | 40 ft-lbf (54 N·m), in three steps |
| 3Y-EC | 2.0 L OHV 8V | 1984–1985 | 14 mm bolts 65 ft-lbf (88 N·m); 12 mm bolts 14 ft-lbf (19 N·m) |
| 4Y-EC | 2.2 L OHV 8V | 1986–1990 | 14 mm bolts 65 ft-lbf (88 N·m); 12 mm bolts 14 ft-lbf (19 N·m) |
| 20R | 2.2 L SOHC 8V | 1975–1980 | 53–63 ft-lbf (72–85 N·m), in three steps |
| 22R, 22REC | 2.4 L SOHC 8V | 1981–1986 | 58 ft-lbf (79 N·m), in three steps |
| 22R, 22R-E, 22REC | 2.4 L SOHC 8V | 1987–1995 | 58 ft-lbf (79 N·m), in three steps |
| 22R-TEC (turbo) | 2.4 L SOHC 8V | 1985–1989 | 58 ft-lbf (79 N·m), in three steps |
Diesel engines
| Engine | Displacement | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|
| 1C (1CLC) | 1.8 L SOHC 8V | 1984–1985 | 62 ft-lbf (84 N·m), in three steps |
| 1C-T (1CTLC) turbo | 1.8 L SOHC 8V | 1984–1986 | 62 ft-lbf (84 N·m), in three steps |
| 2C-T (2CTLC) turbo | 2.0 L SOHC 8V | 1986 | 1st 33 ft-lbf (45 N·m), 2nd +90°, 3rd +90° |
| L | 2.2 L SOHC 8V | 1981–1983 | 84–90 ft-lbf (114–122 N·m), in three steps |
| 2L | 2.4 L SOHC 8V | 1984–1987 | 84–90 ft-lbf (114–122 N·m), in three steps |
| 2L-T turbo | 2.4 L SOHC 8V | 1984–1987 | 84–90 ft-lbf (114–122 N·m), in three steps |
6-cylinder and V6 engines
| Engine | Displacement | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|
| 2M | 2.3 L SOHC 12V | 1967–1972 | 12 mm bolts 54–61 ft-lbf (73–83 N·m); 8 mm bolts 11–16 ft-lbf (15–22 N·m) |
| 4M | 2.6 L SOHC 12V | 1971–1979 | 12 mm bolts 54–61 ft-lbf (73–83 N·m); 8 mm bolts 11–16 ft-lbf (15–22 N·m) |
| 4M-E | 2.6 L SOHC 12V | 1979–1980 | 12 mm bolts 55–61 ft-lbf (75–83 N·m); 8 mm bolts 11–15 ft-lbf (15–20 N·m) |
| 5M-E | 2.8 L SOHC 12V | 1981–1982 | 12 mm bolts 55–61 ft-lbf (75–83 N·m); 8 mm bolts 11–15 ft-lbf (15–20 N·m) |
| 5M-GE | 2.8 L DOHC 12V | 1982–1988 | 58 ft-lbf (79 N·m), in three steps |
| 7M-GE | 3.0 L DOHC 24V | 1986–1992 | 58 ft-lbf (79 N·m), in three steps |
| 7M-GTE (turbo) | 3.0 L DOHC 24V | 1987–1992 | 58 ft-lbf (79 N·m), in three steps |
| 2VZ-FE | 2.5 L DOHC 24V | 1988–1992 | 12-point bolts: 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 3VZ-E | 3.0 L SOHC 12V | 1988–1995 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd 33 ft-lbf (45 N·m), 3rd +90°, 4th +90°; bolt 9: 27 ft-lbf (37 N·m) |
| 3VZ-FE | 3.0 L DOHC 24V | 1992–1993 | 12-point bolts: 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 5VZ-FE | 3.4 L DOHC 24V | 1995–2004 | 12-point bolts: 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 1MZ-FE | 3.0 L DOHC 24V | 1994–2006 | 12-point bolts: 1st 40 ft-lbf (54 N·m), 2nd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 3MZ-FE | 3.3 L DOHC 24V | 2004–2008 | 12-point bolts: 1st 40 ft-lbf (54 N·m), 2nd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 3MZ-FXE (hybrid) | 3.3 L DOHC 24V | 2006–2008 | 12-point bolts: 1st 40 ft-lbf (54 N·m), 2nd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 2JZ-GE | 3.0 L DOHC 24V | 1993–1998 | 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90° |
| 2JZ-GTE (turbo) | 3.0 L DOHC 24V | 1993–1998 | 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90° |
| 2GR-FE | 3.5 L DOHC 24V | 2005–2008 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| 1GR-FE | 4.0 L DOHC 24V | 2003–2008 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| F | 3.9 L OHV 12V | 1967–1974 | 83–98 ft-lbf (113–133 N·m), in three steps |
| 2F | 4.2 L OHV 12V | 1975–1987 | 83–98 ft-lbf (113–133 N·m), in three steps |
| 3F-E | 4.0 L OHV 12V | 1988–1992 | 90 ft-lbf (122 N·m), in three steps |
| 1FZ-FE | 4.5 L DOHC 24V | 1993–1997 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
V8 engines
| Engine | Displacement | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|
| 2UZ-FE | 4.7 L DOHC 32V | 1998–2004 | 1st 24 ft-lbf (33 N·m), 2nd +90°, 3rd +90° |
| 2UZ-FE | 4.7 L DOHC 32V | 2005–2008 | 1st 30 ft-lbf (41 N·m), 2nd +90°, 3rd +90° |
| 3UR-FE | 5.7 L DOHC 32V | 2007–2008 | Bolts 1–10: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 11–12: 15 ft-lbf (20 N·m) |
Frequently asked questions
Can I reuse Toyota head bolts?
Bolts tightened by angle (“+90°”) are stretch bolts. Toyota allows reuse only if they are within the length or diameter limit given in the repair manual. In practice, most technicians replace them every time.
Why are there two different specs for the 2AZ-FE?
Earlier 2AZ-FE engines (Camry/Solara 2002–2006, RAV4 2004–2005, Highlander 2001–2007) use 58 ft-lbf (79 N·m) plus 90°, while later engines (2007–2008 Camry, 2006–2008 RAV4 and the 2AZ-FXE hybrid) use 52 ft-lbf (71 N·m) plus 90°. The 2AZ-FE is also known for stripped head bolt threads in the block: check the threads carefully and repair them with a proper insert if needed.
Where do I find the tightening sequence?
The sequence diagram is in the Engine Mechanical section of the repair manual for your engine, and is usually supplied with the head gasket set. You can also check other torque values for your engine in our Toyota torque specification lookup.
Source: Fel-Pro (Federal-Mogul) Torque Tables – Complete Cylinder Head Torque Specifications, 2009 edition, Toyota section. N·m values are converted from ft-lbf and rounded. This is an aftermarket reference: always confirm the specification, sequence and bolt limits in the Toyota repair manual for your engine before working on it. See also our Toyota owner’s manuals.
Lexus engines are Toyota engines, and they use the same tightening methods: torque plus angle on stretch bolts, in a strict sequence. This page lists the cylinder head bolt torque specifications for Lexus V6 and V8 engines from 1990 to 2008 – from the ES 250’s 2VZ-FE to the LS 400’s 1UZ-FE, the GS/IS 2JZ-GE and the LS 600h’s 2UR-FSE – with every value in ft-lbf and N·m.
How to read the tables
- “1st 29, 2nd +90°”: tighten all bolts in sequence to 29 ft-lbf (39 N·m), then turn each one a further 90° in the same sequence.
- “Bolts 1–8 … bolts 9–10”: the main head bolts are tightened by torque plus angle, then the smaller bolts at the end of the head by torque only. The numbers refer to the tightening sequence.
- 12-point and recessed bolts (2VZ-FE, 3VZ-FE, 1MZ-FE, 3MZ-FE): the 12-point head bolts are tightened by torque plus angle; the recessed bolts last, by torque only.
- Bolts tightened by angle are torque-to-yield (stretch) bolts: check their length against the repair manual limit and replace them if in doubt.
- Oil the threads and the underside of the bolt heads lightly, blow out the bolt holes, and always follow the sequence from the centre outwards.
Lexus 6-cylinder and V6 engines
| Engine | Displacement | Used in (examples) | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|---|
| 2VZ-FE | 2.5 L DOHC 24V | ES 250 | 1990–1991 | 12-point bolts: 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 3VZ-FE | 3.0 L DOHC 24V | ES 300 | 1992–1993 | 12-point bolts: 1st 25 ft-lbf (34 N·m), 2nd +90°, 3rd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 1MZ-FE | 3.0 L DOHC 24V | ES 300, RX 300 | 1994–2003 | 12-point bolts: 1st 40 ft-lbf (54 N·m), 2nd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 3MZ-FE | 3.3 L DOHC 24V | ES 330, RX 330 | 2004–2006 | 12-point bolts: 1st 40 ft-lbf (54 N·m), 2nd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 3MZ-FXE (hybrid) | 3.3 L DOHC 24V | RX 400h | 2006–2008 | 12-point bolts: 1st 40 ft-lbf (54 N·m), 2nd +90°; recessed bolts 13 ft-lbf (18 N·m) |
| 2JZ-GE | 3.0 L DOHC 24V | GS 300, IS 300, SC 300 | 1992–2005 | 1st 26 ft-lbf (35 N·m), 2nd +90°, 3rd +90° |
| 4GR-FSE | 2.5 L DOHC 24V | IS 250 | 2006–2008 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| 3GR-FSE | 3.0 L DOHC 24V | GS 300, IS 300 | 2006 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| 2GR-FE | 3.5 L DOHC 24V | ES 350, RX 350 | 2007–2008 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| 2GR-FSE | 3.5 L DOHC 24V | GS 350, IS 350 | 2006–2008 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| 2GR-FSE (hybrid) | 3.5 L DOHC 24V | GS 450h | 2007–2008 | Bolts 1–8: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 9–10: 22 ft-lbf (30 N·m) |
| 1FZ-FE | 4.5 L DOHC 24V | LX 450 | 1996–1997 | 1st 29 ft-lbf (39 N·m), 2nd +90°, 3rd +90° |
Lexus V8 engines
| Engine | Displacement | Used in (examples) | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|---|
| 1UZ-FE | 4.0 L DOHC 32V | LS 400, SC 400, GS 400 | 1990–1997 | 1st 29 ft-lbf (39 N·m), 2nd +90° |
| 1UZ-FE | 4.0 L DOHC 32V | LS 400, SC 400, GS 400 | 1998–2000 | 1st 29 ft-lbf (39 N·m), 2nd +90° |
| 3UZ-FE | 4.3 L DOHC 32V | LS 430, GS 430, SC 430 | 2001–2008 | 1st 44 ft-lbf (60 N·m), 2nd +90° |
| 2UZ-FE | 4.7 L DOHC 32V | LX 470, GX 470 | 1998–2004 | 1st 24 ft-lbf (33 N·m), 2nd +90°, 3rd +90° |
| 2UZ-FE | 4.7 L DOHC 32V | LX 470, GX 470 | 2005–2008 | 1st 30 ft-lbf (41 N·m), 2nd +90°, 3rd +90° |
| 1UR-FSE | 4.6 L DOHC 32V | LS 460, GS 460 | 2007–2008 | 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90° |
| 2UR-FSE (hybrid) | 5.0 L DOHC 32V | LS 600h L | 2007–2008 | Bolts 1–10: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 11–12: 15 ft-lbf (20 N·m) |
| 3UR-FE | 5.7 L DOHC 32V | LX 570 | 2008 | Bolts 1–10: 1st 27 ft-lbf (37 N·m), 2nd +90°, 3rd +90°; bolts 11–12: 15 ft-lbf (20 N·m) |
Note on the 1UZ-FE and 3UZ-FE: both use only two steps (torque, then +90°), while the later 2UZ-FE, 1UR-FSE and 3UR-FE use two angle steps. Do not mix up the procedures when working on different generations of the LS, GS and SC.
Source: Fel-Pro (Federal-Mogul) Torque Tables – Complete Cylinder Head Torque Specifications, 2009 edition, Lexus section. N·m values are converted from ft-lbf and rounded; the “Used in” column gives typical models for reference. This is an aftermarket reference: always confirm the specification, sequence and bolt limits in the repair manual for your engine. See also our Toyota cylinder head bolt torque specs and torque specification lookup.
Scion models use Toyota engines, so head bolt tightening follows Toyota practice: torque first, then one or two angle steps in sequence. Here are the cylinder head bolt torque specs for the Scion xA, xB, xD and tC (2003–2008), in ft-lbf and N·m.
Scion cylinder head bolt torque specs
| Engine | Displacement | Used in (examples) | Model years | Head bolt tightening (ft-lbf, N·m) |
|---|---|---|---|---|
| 1NZ-FE | 1.5 L DOHC 16V | xA, xB | 2003–2007 | 1st 22 ft-lbf (30 N·m), 2nd +90°, 3rd +90° |
| 2ZR-FE | 1.8 L DOHC 16V | xD | 2008 | 1st 36 ft-lbf (49 N·m), 2nd +90°, 3rd +45° |
| 2AZ-FE | 2.4 L DOHC 16V | tC, xB (2nd gen.) | 2005–2008 | 1st 58 ft-lbf (79 N·m), 2nd +90° |
The 2ZR-FE in the xD uses a final 45° step, not 90° – an easy mistake if you are used to other Toyota engines. The 2AZ-FE in the tC and second-generation xB uses 58 ft-lbf (79 N·m) plus 90°; this engine is known for stripped head bolt threads in the block, so inspect the threads before reassembly.
How to read the tables
- “1st 29, 2nd +90°”: tighten all bolts in sequence to 29 ft-lbf (39 N·m), then turn each one a further 90° in the same sequence.
- “Bolts 1–8 … bolts 9–10”: the main head bolts are tightened by torque plus angle, then the smaller bolts at the end of the head by torque only. The numbers refer to the tightening sequence.
- 12-point and recessed bolts (2VZ-FE, 3VZ-FE, 1MZ-FE, 3MZ-FE): the 12-point head bolts are tightened by torque plus angle; the recessed bolts last, by torque only.
- Bolts tightened by angle are torque-to-yield (stretch) bolts: check their length against the repair manual limit and replace them if in doubt.
- Oil the threads and the underside of the bolt heads lightly, blow out the bolt holes, and always follow the sequence from the centre outwards.
Source: Fel-Pro (Federal-Mogul) Torque Tables – Complete Cylinder Head Torque Specifications, 2009 edition, Scion section. N·m values are converted from ft-lbf and rounded; the “Used in” column gives typical models for reference. This is an aftermarket reference: always confirm the specification, sequence and bolt limits in the repair manual for your engine. See also our Toyota cylinder head bolt torque specs and torque specification lookup.
