Toyota Forklift Daily Inspection Checklist (Free Printable PDF)

A forklift should be checked before every shift. Toyota’s operator manuals call this the pre-operation check and make it the responsibility of the user: it takes about 10 minutes and catches most problems – leaks, low tires, weak brakes, damaged chains – before they cause an accident or a breakdown. In the United States, OSHA also requires forklifts to be examined before being placed in service, at least daily, and after each shift when they are used around the clock.

This guide follows the pre-operation check in Toyota’s 8FG/8FD operator’s manual and adds the checks needed for LPG and electric trucks. You can download a free printable checklist at the end of the page.

1. Before you start: safety

  • Park on level ground, forks fully lowered, parking brake applied, engine off and key removed.
  • Check the record or tag from the previous shift: any malfunction reported earlier must be corrected first.
  • Never check under a raised mast or forks, and keep sparks and flames away from fuel and batteries.

2. Walk-around inspection (engine off)

ItemWhat to check
Truck stanceThe truck should not lean to one side – a lean points to a flat tire or an axle problem.
Under the truckOil, coolant, fuel or hydraulic oil on the floor where the truck was parked; loose or damaged parts.
Tires and rimsPressure (pneumatic tires), cuts, chunking, uneven wear, bent rims, objects stuck in the tread. Big wear differences between left and right, or front and rear, need attention.
Wheel nutsNone missing or loose. Tighten evenly to the torque in the service data.
Body and overhead guardCracks, bent parts, missing bolts, damaged load backrest.
ForksCracks at the heel, bent tips, uneven fork height, locking pins in place.
Mast, chains and hosesChains evenly tensioned and lubricated, no broken links; no hydraulic leaks on cylinders and hoses; no cracks on the mast.
Lamps and mirrorsLenses clean and undamaged; work lights, warning light and turn signals working.
Data plate and labelsCapacity plate readable and matching the attachment fitted.

3. Engine compartment and fluids (engine cold)

  • Engine oil: with the truck on level ground, the level must be between the F and L marks. Check before starting, or at least 3 minutes after stopping the engine.
  • Coolant: between the reservoir tank marks. Never open the radiator cap on a hot engine. Toyota specifies long-life coolant at 30 % concentration (50 % in very cold climates).
  • Hydraulic oil: with the forks on the ground, check the level on the dipstick attached to the tank cap.
  • Brake fluid: within the marks on the reservoir. A falling level means a leak – have it checked.
  • Radiator: free of paper, dust and debris; no leaks.
  • Fan belt: no cracks; correct tension.
  • Fuel: enough for the shift. Refuel with the engine stopped.

LPG trucks

  • Cylinder correctly positioned and locked in its bracket, locating pin engaged.
  • Hose and coupling undamaged, connection tight, no smell of gas and no frost on fittings.
  • Pressure relief valve pointing up (horizontal cylinders).

Electric trucks

  • Battery charged (check the battery indicator), cables and connector undamaged, battery restraint in place.
  • Lead-acid batteries: electrolyte level correct (add only distilled water, after charging), battery top clean and dry, vent caps in place.

4. Seated checks (engine running)

ItemWhat to check
Seat and seat beltSeat adjusted and locked; belt latches and retracts.
OPS lamp (operator presence system)Sitting on the seat, the OPS lamp must go out. If it stays on, or does not come on when you leave the seat, report it.
Instruments and warning lampsAll work; no warning lamp stays on and no error code is displayed.
HornSounds clearly.
EngineNo abnormal noise or vibration. Exhaust colour: clear or light blue is normal; black means incomplete combustion, white means burning oil.
SteeringNo excessive play, looseness, vibration or pulling to one side.
Service brakePedal play correct, pedal does not sink when held, truck stops straight.
Inching / clutch pedalCorrect play, smooth operation, no abnormal resistance.
Parking brakeHolds the truck; releases fully.
Lift, tilt and attachmentsSmooth movement, no jerking or unusual noise, no drifting, no leaks. On trucks with SAS (System of Active Stability), make sure it is working – no SAS warning.
Travel alarm and lightsReverse alarm and lights working.

5. If you find a problem

Do not use the truck. Tag it “Out of service”, record the fault on the checklist and inform your supervisor. Faults in brakes, steering, mast, chains, forks or the hydraulic system must be repaired by a qualified technician before the truck goes back to work.

Weekly checks (every 40 hours)

Every 40 hours (weekly), Toyota adds these items to the daily check on 8FG/8FD trucks:

  • Air cleaner: clean the element (wash it in water with neutral detergent and let it dry naturally – never use compressed air or a flame). Replace it after six washes or one year.
  • Fan belt: inspect for cracks, fraying and tension.
  • Torque converter oil level (torque converter models): check.
  • Battery electrolyte level: check.
  • Bolts and nuts: retighten.
  • Mast and steering linkage: grease.
  • Lift chains: lubricate with engine oil.

The full service schedule is in our Toyota 8FG/8FD maintenance schedule.

Free printable checklist

Print one sheet per truck per week: it has a column for each day, space for the operator’s initials and a box to report faults.


Source: Toyota 8FG/8FD 10–35 forklift operator’s manual (pre-operation check and periodic maintenance sections); OSHA 29 CFR 1910.178(q)(7). Always follow the operator’s manual for your truck and your company’s safety rules. See also our Toyota forklifts section.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top