Toyota 8FBN Electric Forklift Guide: Battery, Maintenance and Specifications

The Toyota 8FBN is a four-wheel electric counterbalanced forklift in the 1.5 to 3 tonne range, with AC drive and pump motors. This guide covers what owners and technicians need most: models and battery voltage, battery choice and minimum battery weight, battery care and testing, the maintenance schedule, fluid capacities, tire pressures and motor data. All values come from the Toyota 8FBN15–30 repair manual (Volume 1).

8FBN models

SeriesModelsBattery voltage
1 ton series8FBN15, 8FBN18 (plus 50-8FBN15, 8FBN16 and 50-8FBN18 for China)48 V
2 ton series8FBN20, 8FBN25 (plus 50-8FBN20 for China)48 V
3 ton series8FBN3080 V

The number gives the capacity class: 15 = 1.5 t, 18 = 1.8 t, 20 = 2.0 t, 25 = 2.5 t, 30 = 3.0 t.

Batteries: size, capacity and minimum weight

On an electric forklift the battery is also part of the counterweight. A battery that is too light reduces stability and can make the truck tip forward with a load. Toyota therefore gives a minimum battery weight for each model. If you buy a battery locally, it must fit the compartment and weigh at least this much – add ballast if needed.

ModelVoltageCompartment (L × W × H)Battery capacities offered *Minimum battery weight
8FBN15, 8FBN16, 8FBN1848 V459 or 548 × 996 × 627 mmwithin 390–725 Ah629 kg (1,387 lb)
50-8FBN15, 50-8FBN1848 V459 or 548 × 996 × 627 mmwithin 390–725 Ah628 kg (1,385 lb)
8FBN2048 V548 or 655 × 996 × 627 mmwithin 390–725 Ah696 kg (1,534 lb)
50-8FBN2048 V548 or 655 × 996 × 627 mmwithin 390–725 Ah672 kg (1,482 lb)
8FBN2548 V655 × 996 × 627 mmwithin 390–725 Ah805 kg (1,775 lb)
8FBN3080 V730 × 1,058 × 627 mm370–480 Ah964 kg (2,125 lb)

* The exact capacities available depend on the compartment length and legroom version of each truck. Toyota lists batteries from GS Yuasa, Shin-Kobe and Anhui built to JIS, DIN or BS standards; some are available with an automatic watering system. Check the table in the repair manual for your exact truck.

Battery service standards

ItemJIS and BS batteriesDIN batteries (GS Yuasa)
Specific gravity, fully charged (20 °C / 68 °F)1.2801.297
Specific gravity, end of discharge (20 °C / 68 °F)1.1501.167
Discharge end voltage42.5 V on 48 V batteries · 68 V on 80 V batteries
ElectrolyteRefined dilute sulfuric acid
Fluid to addDistilled water only
Insulation resistance (battery to case)1 MΩ or more

How to check a forklift battery

  1. Electrolyte level. Open the cap: if the white line on the red float has dropped, add distilled water just until the white line appears. Stop as soon as it shows – if the float tip touches the stopper, you have added too much.
  2. Electrolyte condition. Normal electrolyte is clear and colourless. If it is cloudy, take a sample in a beaker to check – cloudy electrolyte points to shed plate material or contamination.
  3. Specific gravity. Use a hydrometer: draw electrolyte into the tube, let the float hang freely without touching the sides, and read the scale at the top of the liquid once the bubbles have gone. Correct the reading to 20 °C with this formula:
    S20 = St + 0.0007 × (t − 20)
    where St is the reading and t the electrolyte temperature in °C. Example: a reading of 1.270 at 35 °C gives 1.270 + 0.0007 × 15 = about 1.280 – fully charged.
  4. Insulation resistance. Measure between the battery terminals and the battery case with a megohmmeter. Below 1 MΩ, remove the battery, wash it with water, let it dry completely and measure again; refit it only when it reads 1 MΩ or more. Low insulation resistance causes current leakage and can trigger faults.
  5. Keep a record. Toyota recommends a control sheet for each battery: date, cell number, specific gravity, electrolyte temperature, water added, remarks and inspector. Comparing readings over time shows weak cells early.

What damages forklift batteries

  • Sulfation – from leaving the battery discharged, long storage without charging, low electrolyte or improper charging.
  • Plate warping and shedding – from repeated over-discharge or overcharge, too high a charging current or high ambient temperature.
  • Electrolyte loss – from overcharging, cracked cells or poor watering.
  • Short circuits – from a damaged separator or shed material collecting at the bottom of the cell.
  • Loose or corroded connections – from fouled terminals or a dirty connecting plug.

Simple rules: charge before the battery is fully flat (do not run below the discharge end voltage), let the charger finish its cycle, add water after charging rather than before, keep the battery top clean and dry, and never store a battery discharged.

Maintenance schedule

Like the engine trucks, the 8FBN is serviced every 250 hours (6 weeks), 500 hours (3 months), 1,000 hours (6 months) and 2,000 hours (12 months) – whichever comes first. Electrical checks specific to electric trucks:

ComponentEvery 250 hFrom 500 hEvery 2,000 h
MotorsRotation soundInsulation resistance–
BatteryCharge level, electrolyte level, specific gravity, connections, top of caseInsulation resistanceVoltage of each cell after charging
ChargerTimer function, terminal tightnessVoltage measurementMagnetic switch contacts
Magnet contactorContacts and auxiliary contact condition–Arc chute, timing, coil and main lead mounting
ControllerOperation; clean inside–Motor input voltage
Switches, fuses, wiringMicro switches, direction switch, fuses, harness, battery connector and AC plug––

The usual chassis checks also apply at each service: brakes, steering, tires, mast and chains, hydraulic oil and leaks, overhead guard, lights, horn, seat belt and seat switch, and the SAS stability system. Use our daily inspection checklist before every shift.

Replacement intervals

Part / fluidInterval
Hydraulic oil filterFirst 250 h on a new truck, then every 1,000 h (6 months)
Hydraulic oilEvery 1,000 h (6 months)
Brake fluidEvery 1,000 h (6 months)
Drive unit oilEvery 2,000 h (12 months)
Wheel bearing greaseEvery 2,000 h (12 months)
Brake master cylinder rubber parts, wheel cylinder cupsEvery 2,000 h (12 months)
Brake reservoir hose, power steering hose and rubber parts, hydraulic hosesEvery 2 years
Lift chainsEvery 3 years

Fluid capacities

Item1 t series2 t series3 t seriesType
Drive unit4.0 L (1.06 US gal)4.2 L (1.11 US gal)5.0 L (1.32 US gal)Hypoid gear oil, API GL-4, SAE 75W grade (the manual prints “75W-82W” – confirm the exact grade with your Toyota dealer)
Hydraulic oil, V/FSV mast, lift up to 5,500 mm (3 t: up to 4,700 mm)17.5 L (4.6 US gal)17.5 L (4.6 US gal)19.1 L (5.0 US gal)Standard: hydraulic oil ISO VG 32 class (Toyota specifies Daphne Super Hydro 32AT; cold-storage models Daphne Hydro GT-T)
Hydraulic oil, V/FSV mast, 6,000 mm lift18.9 L (5.0 US gal)18.9 L (5.0 US gal)22.0 L (5.8 US gal)
Brake lineAs requiredSAE J1703 DOT 3 (cold-storage: Arctic S type)
Chassis grease pointsAs requiredMP grease
BatteryAs requiredDistilled water

Hydraulic oil quantities are for trucks without attachments. FV (full free) masts use the same quantities at lower lift heights – check the table in the manual for your mast.

Tire pressures

ModelTireSizeRimPressure
1.5 tStandard6.00-9-10PRDivided700 kPa (7.0 kgf/cm², 101.5 psi)
Oversize single6.50-10-10PRDivided775 kPa (7.75 kgf/cm², 112.4 psi)
1.6–1.8 tStandard6.50-10-10PRDivided775 kPa (7.75 kgf/cm², 112.4 psi)
1.5–1.8 tSpecial single21×8-9 (10PR or 14PR)Side ring625 kPa (6.25 kgf/cm², 90.6 psi)
2.0–2.5 tStandard21×8-9-14PRDivided900 kPa (9.0 kgf/cm², 130.5 psi)
3 tStandard28×9-15-14PRSide ring800 kPa (8.0 kgf/cm², 116.0 psi)

Safety: never inflate above the specified pressure, inflate a removed wheel only inside a safety cage, and always let all the air out before taking a divided rim apart – the rim halves can separate violently under pressure.

Drive and pump motors

All 8FBN trucks use three-phase AC motors, with a rotation sensor on each motor. Standard specification ratings (60-minute rating):

ModelsDrive motorPump motor
8FBN15, 16, 18, 50-8FBN207.6 kW, 29 V, 36 kg9.5 kW, 25 V, 32 kg
8FBN20, 2510.7 kW, 28 V, 46 kg12.2 kW, 26 V, 37 kg
8FBN3011.9 kW, 50 V, 49 kg14.4 kW, 48 V, 42 kg
50-8FBN154.8 kW, 28 V, 32 kg7.0 kW, 26 V, 26 kg

Motor weights exclude the drive unit case. At each service, listen for abnormal rotation noise, and from 500 hours measure the motor insulation resistance; a noisy bearing should be replaced before it damages the rotor.

Main component weights

Component1 t series2 t series3 t series
Front module (without tires)about 300 kgabout 340 kgabout 435 kg
Rear axle (without tires)about 85 kgabout 88 kgabout 110 kg
V mast with lift bracket, 3,000 mm liftabout 380 kgabout 450 kgabout 550 kg
Counterweightabout 355 kg (1.5–1.6 t) · 520 kg (1.8 t)about 535 kg (2.0 t) · 840 kg (2.5 t)about 845 kg

More 8FBN data: brake service data and the battery charger guide.


Source: Toyota 8FBN15, 16, 18, 20, 25, 30 forklift repair manual, Volume 1 – vehicle models, battery section, periodic maintenance, lubricants, tires and motor specifications. Imperial and US units are converted and rounded. Always confirm values for your truck’s serial number and options. See all our Toyota forklift guides.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top